Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Placentia Homeowners Choose CGI Construction
Square Deal Contractors provides independent CGI cabinetry service and installation across Placentia, focusing on the failure modes this brand actually exhibits in local homes: peeling thermofoil drawer edges, cracked painted MDF door miters, and sagging particleboard box floors. We’re not a CGI dealer or authorized warranty center, but we’ve corrected and installed CGI cabinet runs throughout 92870 and 92871 for years, which means we can match door profiles and sheens that most generic remodelers miss entirely. If you own CGI cabinets in Placentia and they’re showing age or damage, call (866) 623-7205 for an honest assessment.
Why Trust Square Deal Contractors for Your CGI Construction?
We read CGI’s box construction, drawer glide systems, and finish specs on a near-daily basis. That familiarity matters when a Lancaster shaker door chips at the corner miter or a Dakota thermofoil drawer front starts peeling along its bottom edge. We know why it’s happening and whether the fix is a replacement door front or a box-floor reinforcement. Nolan Breckett, our owner, spent his early years in construction technology coursework at Saddleback College and has built his reputation across South Orange County by being straight about what a cabinet run needs and what it doesn’t. When we tell a Placentia homeowner their CGI boxes are worth keeping and only the doors need replacing, that’s a sequenced, material-based judgment, not a guess. We’re an independent CGI service provider, which means our recommendation isn’t shaped by a manufacturer’s program or a quota. It’s shaped by what’s actually on the wall in front of us.
Styles & brands we work with
Common CGI Construction Problems We Fix in Placentia
- Thermofoil peeling on Dakota and Park Avenue door lines. CGI’s white and antique thermofoil fronts delaminate along drawer edges and door bottoms, especially in Placentia kitchens that catch heavy morning sun or sit through Santa Ana heat cycles. The vinyl layer separates from the MDF core, and once it starts, moisture gets in and accelerates the peel. We replace the failed fronts with matched painted shaker doors or genuine CGI foil fronts when the run is still young enough to match.
- Cracked miter joints on Lancaster and Dover painted shaker doors. Painted MDF shaker doors chip and hairline-crack where the rails meet the stiles. This is a construction issue with the door frame itself, not the hinge or the install. The corners flex with seasonal humidity shifts, and the paint film can’t stretch with them. We replace the affected doors or the full run, depending on how many miters have opened up.
- Sagging particleboard box floors under sinks and cookware loads. Older CGI installs with particleboard boxes, especially under a stone sink or a heavy pot drawer, show a visible dip across the cabinet floor. Doors rack, rub, and stop closing flush. We reinforce the box floor from beneath, re-shim the cabinet, and re-align the doors. When the box is too compromised, we swap the cabinet rather than patch it indefinitely.
- Loose soft-close hinges pulling out of MDF door frames. The screw holes in painted MDF doors wallow out over time, and the hinge loses its bite. Doors drift, hang slightly open, and refuse to latch flush. We re-secure hinges into solid frame stock or install threaded inserts, depending on the door’s remaining material.
- Drawer glide failures on raised-panel oak and maple lines. Older CGI raised-panel runs with side-mount or bottom-mount glides wear out, leaving drawers that stick halfway or drop when pulled. We replace slides with quality aftermarket soft-close hardware where the box dimensions allow, and we match the drawer front profile so the replacement doesn’t look like a patch job.
CGI Parts & Our Repair-vs-Replace Approach
We source genuine CGI doors, drawer boxes, hinges, and touch-up finish kits through the manufacturer’s parts channel so any refaced or repaired run matches the cabinetry that’s already in the home. For internal hardware and slides, where fit allows, we use quality aftermarket soft-close components, and we tell owners that plainly. The repair-vs-replace conversation is straightforward: if your boxes are square, dry, and solid, we replace doors and drawer fronts and keep the cabinet run alive. If the box floors have sagged past reinforcement or the foil has delaminated across most of the run, we’ll say so and price a replacement honestly rather than chasing a repair that won’t hold. Call (866) 623-7205 and we’ll give you the same straight answer on your CGI cabinets in Placentia.
Our CGI Service Process – Step by Step
- 1
Diagnosis. We inspect every door, drawer front, hinge point, and box floor in the run. We’re looking for the CGI-specific failure modes: foil separation, miter cracks, box sag, hinge wallowing. We also check for non-permitted prior work, which Placentia’s older housing stock has in abundance, since it can affect whether a larger remodel triggers code requirements.
- 2
Repair or replace recommendation. We show you what’s failing and why, then give you a line-item scope. You’ll know exactly which doors are being replaced, which boxes are being reinforced, and what the countertop installation involves if that’s part of the job.
- 3
Repair or installation. We remove the failed components, prep the boxes, install genuine CGI-matched doors and drawer fronts or full cabinet runs, and set countertops when the project includes quartz or granite. Every hinge is re-secured into solid stock, not reamed MDF.
- 4
Testing and alignment. We open and close every door and drawer, check soft-close function, verify flush latching, and confirm the countertop is level and sealed.
- 5
Warranty and follow-up. Our workmanship warranty covers the labor we perform. We’ll tell you what’s covered, what’s not, and when to call us back if something shifts.
See the difference
Before
After
Before
After
Before
AfterCGI Products We Service & Install in Placentia
We work on the full span of CGI’s cabinet lines: the Lancaster and Dover painted shaker series, Dakota and Park Avenue thermofoil doors, the maple and oak raised-panel families with plywood box upgrades, the all-plywood Premier series, and CGI’s semi-custom vanity cabinets. We stock common soft-close hinge replacements, drawer glides, and touch-up kits for fast turnaround on repairs across Placentia. We also install new CGI cabinet runs when a full kitchen remodel calls for it, paired with quartz or granite countertops as the project demands. Our work spans cabinet installation, cabinet refacing, and countertop installation across 92870 and 92871.
We Also Service These Brands
While our CGI-specific knowledge runs deep, we’re a full-scope general contractor, not a single-brand shop. That means we also install and service cabinets from KraftMaid, work with Cambria and Silestone countertops, and fit Kohler plumbing fixtures throughout Placentia kitchens and bathrooms, plus CGI service in Foothill Ranch. One contractor, every phase.
FAQs – CGI Construction Service in Placentia
No, we’re an independent CGI service provider. We’re not affiliated with CGI or authorized by them, which means our repair recommendations aren’t steered by any manufacturer program. We source genuine CGI parts through the parts channel and match door profiles and finishes accurately, but we work for you, not for the brand.
Yes, for doors, drawer boxes, hinges, and finish kits, we use genuine CGI components so refaced and repaired runs match the existing cabinetry. For internal slides and soft-close hardware where fit allows, we use quality aftermarket components that perform as well or better, and we’ll tell you which is which before any work starts.
Most door and drawer front replacements take one to two days once the parts arrive. Full cabinet refacing on a mid-size Placentia kitchen typically runs three to five working days, and a full cabinet install with countertops lands in the one-to-two-week range depending on scope. Exact timing depends on the cabinet run and what we find behind it. Call (866) 623-7205 for a project-specific estimate.
We service Lancaster and Dover painted shaker lines, Dakota and Park Avenue thermofoil doors, maple and oak raised-panel families, the all-plywood Premier series, and CGI semi-custom vanities. If your Placentia home has CGI cabinets from a line not listed here, call us and we’ll identify what you have and whether we can source the parts.
Repairs performed by an independent contractor can affect manufacturer warranty coverage depending on what’s done and whether genuine CGI parts are used. We use OEM components for anything visible or structural, and we’ll tell you upfront if a specific repair could impact your remaining warranty before you approve the work.
Cabinet installation runs $4,000 to $13,000, countertop installation $2,000 to $6,500, a full kitchen remodel $14,000 to $45,000, and a small kitchen remodel $9,000 to $20,000. Refacing an existing CGI run typically lands at the lower end of those ranges since the boxes stay in place. Call (866) 623-7205 for an exact quote, estimates are free.
Here’s a clearer range breakdown for Placentia CGI work:
| Service | Typical Range |
|---|---|
| Cabinet Installation | $4,000 – $13,000 |
| Countertop Installation | $2,000 – $6,500 |
| Kitchen Remodel | $14,000 – $45,000 |
| Small Kitchen Remodel | $9,000 – $20,000 |
Yes, we match the door profile, finish, and sheen to the existing run, so a few replaced doors blend with the rest of the kitchen. This works best when the cabinet line is still in production or the finish is a standard CGI color. For older or discontinued lines, we’ll show you the closest match and let you decide before ordering.
If the peeling is limited to a few drawer fronts and the underlying MDF is dry, we replace those fronts and match them to the run. If the delamination is widespread across most doors and drawer edges, replacement fronts are the honest call, since patching peeling thermofoil rarely holds. Call (866) 623-7205 and we’ll look at your run in person.
The most common cause is either sagging particleboard box floors pulling the face frame out of square, or soft-close hinge screws loosened in MDF door frames. We fix both: reinforcing the box from beneath and re-securing hinges into solid frame stock. The doors stop rubbing and close flush again.
The all-plywood Premier series holds up best under quartz’s weight, especially at the sink base and island. Plywood box floors resist the sag that particleboard runs develop under stone. If your Placentia home has older particleboard CGI boxes, we’ll reinforce them before setting any quartz top.
Yes, when the boxes are square, dry, and solid. Refacing replaces doors, drawer fronts, and veneer while keeping the existing boxes in place, which costs less than a full tear-out and preserves the kitchen’s layout. We’ll tell you within the first visit whether your CGI run is a reface candidate or a replace job. Know what you’re getting into before the first nail goes in.
Book Your CGI Service in Placentia, CA
If your CGI cabinets are peeling, sagging, or misaligned, call (866) 623-7205. We’ll assess the run honestly, tell you whether to repair, reface, or replace, and give you a free line-item estimate. Nolan and the Square Deal Contractors team serve Placentia and the surrounding North Orange County area, including Lake Forest CGI service.
Written by Nolan Breckett, Owner at Square Deal Contractors, serving Placentia and North Orange County.